Comparison between BJX10M-TDT-C, BRQPS700-DDTA-C-P, BS5-F1M-P
Name
BJX10M-TDT-C
BRQPS700-DDTA-C-P
BS5-F1M-P
Category
Sensing Type
Through-beam type
Diffuse reflective type
Through-beam type
Sensing Distance
10m
700mm
5mm
Sensing Target
Opaque material of min. 15mm
Opaque, Translucent material
Opaque
Light Source
Red LED (660nm)
Red LED (660nm)
Infrared LED
Response Time
Max. 1ms
Max. 1ms
Light ON: Max. 20,
Dark ON: Max. 100
Power Supply
10-30VDC ±10% (ripple P-P: max. 10%)
10-30VDC ±10% (ripple P-P: max. 10%)
5-24VDC ±10%(ripple P-P : max. 10%)
Current Consumption
Emitter/Receiver: Max. 20mA
Max. 30mA
Max. 30mA
Sensitivity Adjustment
Sensitivity Adjuster
Sensitivity Adjuster
Operation Mode
Light ON/Dark ON (set by switch)
Light ON/Dark ON (set by control wire)
Light ON/Dark ON (set by control wire)
Control Output
NPN Open Collector
PNP Open Collector
PNP open collector
Connection Type
4mm, 3-wire, 2m (emitter of through-beam type: 4mm, 2-wire, 2m)
(AWG26, core diameter: 0.52mm, number of cores: 20, insulator out diameter: 1mm)
Connector type(M12)
3 mm, 4-wire, 1m
Environment_Ambient Illumination
Sunlight: Max. 11,000lx, Incandescent lamp: Max. 3,000lx (received illumination)
Sunlight: Max. 11,000lx, Incandescent lamp: Max. 3,000lx (received illumination)
Fluorescent lamp: Max. 1,000lx(received illumination)
Environment_Ambient Temperature
-25 to 60℃, storage: -40 to 70℃
-25 to 60℃, storage: -30 to 70℃
-20 to 55℃, storage : -25 to 85℃
Protection Structure
IP65 (IEC standard)
IP67
IP50 (IEC standard)
Environment_Ambient Humidity
35 to 85% RH, storage: 35 to 85% RH
35 to 85% RH, storage: 35 to 85% RH
35 to 85% RH, storage: 35 to 85% RH
Accessories Common
Mounting bracket, M3 bolt: 4, adjustment screwdriver
M18 fixing nut: 2, adjustment screwdriver
Weight
Approx. 65g (approx. 12g)
Approx. 120g(approx. 25g)
Approx. 50g
Hysteresis (Distance)
Max. 20% at rated sensing distance
≤0.05mm
Min. Sensing Target
≥0.8mm×2mm
Response frequency
2kHz
Peak Emission Wavelength
940nm
Indicator
Operation indicator (red LED)
Load Voltage
≤30VDC
Load Current
Max. 100mA
Residual voltage
NPN: ≤1.2VDC, PNP: ≤ 1.2VDC
Protection Circuit
Reverse polarity protection circuit, output overcurrent (short-circuit) protection circuit
Insulation Resistance
≥20 MΩ (250 VDC megger)
Noise Immunity
The square wave noise (pulse width: 1) by the noise simulator ±240VDC
Dielectric Strength
1,000VAC 50/60Hz for 1 minute
Vibration
1.5mm amplitude (max. acceleration 196m/s) at frequency of 10 to 2,000Hz in each X, Y, Z direction for 2 hours
Shock
15,000 m/s (approx. 1,500G) in each X, Y, Z direction for 3 times
Connection
Cable type
Core
AWG28 (0.08mm)
Material
Case: PBT, Sensing part: PC
Selected Product